Axes System Sp. z o.o. conducts its business without damage to the environment, and considers proper handling of worn out electrical and electronic equipment a priority. We are entered in the register of companies held by the General Inspector for the Protection of the Environment as equipment producer and liaise with ELECTRO-SYSTEM Organizacją Odzysku Sprzętu Elektrycznego i Elektronicznego S.A.
Remember to not put worn out equipment with general waste. You could be charged a large fine.
Leave your old equipment with a distributor from whom you buy a new device. Every distributor is required to accept worn out equipment free of charge if you purchase from them the same quantity of new similar equipment. You only need to deliver the equipment to the distributor at your own cost.
Leave worn out equipment at the manufacturer's branch office. An equipment manufacturer undertakes to accept worn out equipment free of charge if you buy from them the same quantity of new similar equipment. You only need to deliver the equipment to the manufacturer at your own cost. You can bring the equipment yourself or contact our office at +48 58 732 19 49 to arrange for a delivery service.
Take your worn out equipment to a collection point. You can find information on a collection point near you on the municipal website or information board at the municipal office, and also at www.remondis-electro.pl.
Leave your equipment at a service point. If repair is economically unreasonable, or not possible for technical reasons, our service is required to accept the device free of charge.
Give away worn out equipment without leaving your home. If you do not have enough time or cannot arrange for transport of your equipment to a collection point, you can use services of a specialised company.
The crossed-out wheelie bin symbol on a product, packaging or user manual means that you should not place the product in the general waste. Users should take their worn out devices to a separate collection point to be recycled.
Let us contact you!
It is very important to us to be in touch with you. Enter your telephone number or e-mail address in the field below, and our representative will contact you to answer any questions concerning the CDIF/3.
Enter your telephone number or e-mail address
Oscilloscope parameters
Shared features of each channel
Sampling
2.4MSPS/channel
Buffer
up to 32K
Time base
10μs/div up to 10s/div
Measuring range
5mV/div up to 2kV/div2
Two standard BNC inputs
Coupling
direct current (DC) or alternating current (AC)
Waveband
1MHz
Impedance
1MΩ/50pF
Max. voltage
±200Vpp
Three additional channels for voltage observation at controller's outputs
Three additional channels for current observation at controller's outputs
Two additional channels for signal observation at generator's outputs
One additional channel for battery voltage observation
Functionality
Advanced operation, display and triggering modes
Triggering from measured signal or from parameter/event of the serial diagnosis
Option of simultaneous observation of signals in all or only selected channels
Possibility to display signals in any physical units using free definable scaling functions
2 Range above 20V/div available for divider probes and high voltage probes.
Generator parameters
One small-signal, precise channel (for sensor emulation)
Output voltage
-2,5V to +2,5V
Current-carrying capacity
up to 50mA
Coupling
direct current (DC) or alternating current (AC)
Sampling
1MSPS
Buffer
up to 32K
Connection socket
BNC3
One high-power channel (for power supply or control)
Output voltage
0V to +25V
Current-carrying capacity
programmable from 0A to 5A
Sampling
1MSPS
Buffer
up to 32K
Connection socket
4mm (so-called banana connector)
Functionality
Direct Digital Synthesis (DDS)
Both channel can operate in asynchronous (separate settings for each channel) or synchronous mode (common settings for both channels)
Ability to generate signals of any shape (arbitral generator)
Built-in library of reference signals, allowing for addition of one's own signals including those recorded with oscilloscope
Ability to generate signals previously recorded with oscilloscope
Automatic operation, triggered operation or operation synchronised by signal from BNC outputs of oscilloscope or parameter/event of the serial diagnosis
3 Output shared with the input of the second channel of the oscilloscope.
Controller parameters
Three independent outputs with defined control level ("+"/"-")
Advanced control modes to facilitate control of stepper motors, three-phase motors, petrol injectors, valves, DC motors , etc.
Pulse-duration modulation or pulse-width modulation of signals from oscilloscope input or with serial diagnosis parameters using free definable scaling functions
Synchronous or asynchronous channel operation
Overvoltage, short circuit, overtemperature and overload protection of outputs
Definable overload protection for each output separately
1 The aggregate current of all channels may not exceed 60A.
Important note: this page uses cookies.
On our website we use cookies to ensure the highest standard of services offered to you. To learn more about cookies, and why we use them on our website, click here.